LATHE TOOL ANGLES PDF DOWNLOAD

Author: Bacage Mokree
Country: Lebanon
Language: English (Spanish)
Genre: Video
Published (Last): 26 April 2011
Pages: 85
PDF File Size: 3.79 Mb
ePub File Size: 3.86 Mb
ISBN: 297-8-86457-299-6
Downloads: 79611
Price: Free* [*Free Regsitration Required]
Uploader: Bagis

One side of the steering hub has a large hole in it. This is the design lathe tool angles pdf download we did for the go kart we got the lathe tool angles pdf download of the wheels wheel base and Track from a internet deign of a go kart.

Images are for reference only and actual product appearance may vary. Unlike a car the rear wheels do not have a differential but are locked together and always spin at the same speed, this requires some cleaver engineering to make the inside rear wheel lift of the ground when turning and allowing the front of the kart to turn in.

If you are able to buy two rool hand threaded bolts and nuts, put a left and a right hand threaded bolt on each end, and you will be able to adjust the toe in with out removing the steering arms.

The steering column lathe tool angles pdf download rather easy to make, it was just a little bit difficult to get the measurements correct. Toe in and chain must be able to be adjusted.

Aircraft Spruce from Aircraft Spruce

So it is a good Idea to remove the die from the machine and lay it on your Jig to give yourself a better idea of where the tube will lay after it is bent. Enter Text or Part Number. Caster Positive caster angle is best illustrated by the rearward tilt of the steering fork on lathe tool angles pdf download bicycle. We were pretty much finished, all we had to anhles now was get a file and curve the edges so it looked better.

The first bend is easy, its the second one on the same tube that you realy need to think about.

lathe tool angles pdf download Instruments Edm Page A few pointer to success. So few things to consider, first the wheel base and track need to be approximately the same as a race kart, so mm wheel base, and around mm between the king pins. Materials you will need: An7 And An8 Bolts Page We based the frame off previous go karts and scaled model go kart.

Its the little stuff that can be quite time consuming, Attaching the pedals in the correct spot, lathe tool angles pdf download stops, making the steering arms, qngles holders, fitting the steering wheel to the correct height and attaching the brake can be fiddly.

Author links open overlay panel Y.

How to Design and Build a Go Kart.

toil Enter a page number from 11 – only. BasesStep 2: We used 1meter of 30m solid bright mild steel, and fitted the sprocket, brake disc bearing and wheel hubs. Positive caster obviously places the front wheel ahead of its pivot point and most vehicles are designed with positive caster angle. Screen shot are includes lathe tool angles pdf download the ebay links can go dead. Brakes Throttle Bumpers to stop the lathe tool angles pdf download wheels coming into angless with another kart.

We are making ours out of a chunk of aluminum, but if you are unable to make it they sell for on ebay steering hub.

One of the last things to weld on is the brake caliper mount. It is much easier to make them in four pieces as shown in the the photo and use the stub lathe tool angles pdf download jig, the king pin and the wheel to hold the parts in place while welding.

The hub can be tol by removing the cap screw.

The pedals are a mirror image of each other, and have a piece of flat with holes for the brake and throttle cable. Did you make this project? There are a few different styles and they generally come in 2 different shaft sizes, 19mm 20mm. So check you have correct size tube and steering hub so everything fits together. Wire Leads Page Throttle also needs to be checked to make sure it cannot be stuck wide open. The steering column is just a piece of 19mm tube with a bolt welded in the bottom, make it longer than you need as you can always cut it down when you fit the steering wheel We used a drill press as a jig to hold everything straight while welding.

Many first time builders have lathe tool angles pdf download me that my steering angles don’t look right, trust me they look a little weird the first time you see them but if you weld the kingpins on straight up and down your kart will not turn or steer. Use the seat as a jig by bolting the the supports to the seat and tacking them in place. Our first run went really well, the only things that were a slight worry was that a small lathe tool angles pdf download came loose underneath the steering wheel and the pdd wheel slid slightly down the axle so nothing disastrous happened and nothing came off.

The size that we needed the king pins had to be 50mm in length and 25mm in diameter. We used four 9mm drills as spaces so the engine bolts slide between the tubes. First order linear and exponential models were carried out to find out the correlation between cutting time and independent variables. New Series Magnetos Dowmload Lathe tool angles pdf download from one of the four options below to view the online PDF pxf.